MaximaLabs
Simulation gallery

NPK 15-15-15 granulation (mixed-acid route)

FertilizerNPKCompound fertilizerGranulationRecycle loopSolidsAmmonia scrubbingCoating
See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

A 50 t/h NPK 15-15-15 granulation plant on the mixed-acid route (EFMA BAT Booklet No. 8, s. 2.1-2.2: the booklet's own standard grade and rate). Phosphoric acid of Handley's (IFA 1984) analysis is ammoniated in a pre-neutralizer to mole ratio 1.45, the solubility maximum on Ivell's (IFA 1984) crystallisation chart; the slurry's water is not typed in but read off that chart at 114 °C: 16.1%. In the granulator the slurry meets a 92% ammonium nitrate solution (Booklet No. 6: up to 8% water for granulation), solid potassium chloride, dolomite filler and the recycle, and more ammonia takes the phosphate to mole ratio 1.53, the ratio the booklet's own pipe-reactor raw-material table implies. (1) The feed rates are not tuned: they are the exact solution of the formulation balances (N, P2O5, K2O, mass and the mole ratio) for 15-15-15 at 1 wt% moisture, from these raw materials, with the coating fixed: 377.8 kg acid, 312.1 kg AN solution, 237.4 kg KCl, 152.4 kg filler and 60.4 kg ammonia per tonne. Against the booklet's 95%-water-soluble pipe-reactor column (nitric acid 242, ammonia 122, P2O5 154, potash 250, filler 150 kg/t) the same solver reproduces its numbers within 3% where the raw materials agree. (2) The product leaves the coating drum at 15.0-15.0-15.0 as-is, 13.89 kg/s (50.0 t/h), with 0.50 kg/t of fatty amine and 9.0 kg/t of kaolin, inside the published anti-caking doses (Breiss, ISMA 1970: 0.4-1.0 kg/t of formulated amine, 8-10 kg/t of mineral charge; GNFC run 0.5 kg/t). The coating dilutes the grade by 0.95%, which the formulation pays for in advance. (3) Recycle ratio 4.5, between Ivell's 'under 4' for a pressure neutralizer and 5-6 for atmospheric systems; product cooled to 315 K. (4) What is an input, and why: the ammonia slips of both reactors and the scrubber recoveries are plant measurements (no measured NH3 vapour pressure over ammonium phosphate slurries was found to compute them). The pre-neutralizer is specified the way a plant quotes it, by the ammonia in its vapour: 0.05 kg NH3 per kg water, the figure Houghtaling & Margiotti (IFA 1994) give for a commercial DAP reactor; the slip that follows is 6.8% of the ammonia fed. (Handley's IFDC pilot-plant slip of 0.29 would put 0.21 kg/kg in the vapour.) The granulator's 0.20 slip is representative, not measured. The stack loses 0.046 kg NH3/t, inside the booklet's 0.06 kg/t BAT level for two 90% scrubbers. (5) At 114 °C and 16% slurry water from 54% P2O5 acid the pre-neutralizer rejects 0.34 MW: with little ammonia slipping, most of the neutralisation heat is released in this vessel, more than boiling off the water needs. (6) Bounded: KCl + NH4NO3 exchange (to KNO3 + NH4Cl) is not modelled (extent 0, an input); the potash is pure KCl (63.2% K2O) where commercial potash is 60%; the 92% AN solution is priced as crystal plus its 3-H2O solution below NBS's first row; Ivell's chart is for pure ammonium phosphate solutions.

The flowsheet

The solved topology — every unit op's real duty, conversion, or split, read straight off a genuine converged solve.

ACID
NH3 PN
NH3 GR
gas
acid
gas
liq
byp
TAIL
gas
acid
gas
liq
byp
PRE
acid
NH3
slurry
vap
NH3
PN
rec
slurry
solids
NH3
gran
gas
NH3
GR
wet
dry
vap
DRY
feed
over
under
SCR1
feed
over
under
SCR2
Crush
Split
feed
gas
elut
solid
COOL
COOL AIR
Product
Stack
Dryer Vapor
NH3 Return PN
NH3 Return GR
Cooler GAS
AN SOL
Potash
Filler
COAT OIL
COAT Powder
prod
coat
out
COAT

The stream table

Every stream's flow, temperature, pressure, and composition — real converged numbers, not placeholders.

See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

Stop fighting legacy software. Build your first flowsheet in 60 seconds.