MaximaLabs
Simulation gallery

Purified phosphoric acid: TBP extraction, scrub and strip

Purified phosphoric acidSolvent extractionTBPFood grade
See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

Food-, technical- and (downstream) battery-grade acid is not made by cleaning wet-process acid of its metals; it is made by extracting the ACID out and leaving the metals behind. Three countercurrent stages of 80 vol% tri-n-butyl phosphate in kerosene take the H3PO4 out of a sulfate-salted 35 wt% feed, three scrub stages against product acid wash the co-extracted impurities back out of the loaded organic, water strips the acid into a clean aqueous liquor, and an evaporator concentrates it. The acid's own distribution ratio is NOT typed in: it comes from Alibrahim's measured single-contact yields (Periodica Polytechnica Chemical Engineering 51(1) 2007 39-42, doi:10.3311/pp.ch.2007-1.07, 80 vol% TBP, equal phase volumes, room temperature) at the feed's own strength, converted from that mass basis to the cascade's mole basis with both phases' mean molar masses -- a factor of about ten for this system, so not optional. Sulfuric acid is the salting agent because the paper measured it as the strongest (H2SO4 > HCl > HNO3 > HClO4) and because a phosphoric plant already has it: 0.8 M lifts the single-contact yield from 12.3% to 16.9%. On that basis alone, three stages at a solvent-to-feed ratio of seven recover 83.9% of the acid, which is the paper's own McCabe-Thiele conclusion ('2 to 3 stages extract 80%') reached from its equilibrium data rather than fitted to its answer. Solved: 10 kg/s of feed acid gives 3.39 kg/s of product at 85.8 wt% H3PO4 (62.2 wt% P2O5) carrying 7 ppm Fe, 11 ppm Ca, 0.5 ppm Zn, 260 ppm S and 1.0% F, with 83.3% of the fed acid reaching it and the rest leaving in an 8 wt% raffinate that goes back to fertilizer-grade acid. Those impurity figures are the paper's own product analysis, reproduced -- which is the point and also the caveat below. HONESTY NOTES, and they matter: (1) NO metal distribution ratio is published with that data, so none ships -- the metals' K_D in the scrub and strip here are BACK-FITTED to the paper's own measured feed-to-product decontamination over its own 3+3-stage circuit (Fe 1850 -> 7 ppm, Ca 613 -> 11, Zn 204 -> nil, S 7350 -> 260), so the impurity rejection is a reproduction of that measurement, not a prediction, and a different acid needs its own leaf test; (2) the model carries no extractant loading, so recovery is overstated at a high organic loading; (3) fluorine is barely rejected here, which is the real behaviour -- the paper's product still held 1% F against 2% in the feed, and a real plant strips it with steam during concentration; (4) the brine package prices a hydrocarbon phase by falling back on its dominant component, so the organic streams' enthalpies are indicative and the cascade is a material balance; (5) the solvent's water uptake, which sets how much water the strip returns, is not measured here; (6) the concentrator is one effect and its product strength is steeply sensitive to its duty -- 10.0 kg/s of steam gives 81 wt% and 10.5 gives 88 -- because the last water is the hardest to remove; a real plant concentrates in several effects under tighter control, which this repo's phosphoric-acid-concentration-* examples show, and above 95 wt% the acid is superphosphoric and outside the water-activity model's range.

The flowsheet

The solved topology — every unit op's real duty, conversion, or split, read straight off a genuine converged solve.

WPA FEED
Solvent
Scrub ACID
Strip Water
feed
solv
ext
raff
Extract
feed
solv
ext
raff
Scrub
feed
solv
ext
raff
Strip
feed
steam
conc
vapor
cond
Concentrator
CONC Steam
PURE ACID
CONC Vapour
CONC Condensate
LEAN Solvent
Raffinate
Scrub Liquor

The stream table

Every stream's flow, temperature, pressure, and composition — real converged numbers, not placeholders.

See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

Stop fighting legacy software. Build your first flowsheet in 60 seconds.