MaximaLabs
Simulation gallery

Wet-process phosphoric acid: hemihydrate reactor-filter, 42% P2O5 off the filter

Phosphoric acidFertilizerHemihydrateWet processFiltration
See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

The hemihydrate (HH) route on the same rock and acid as the wet-process-phosphoric-acid-dihydrate showcase: the attack runs at 98 C, inside the 98-100 C the UNIDO Fertilizer Manual (Section XIII, Phosphoric acid) gives for HH reactors, and the calcium sulfate leaves as bassanite (CaSO4.0.5H2O). That is computed, not assumed: the 42.0% acid's water activity (0.638, from the H3PO4/water model fitted to measured data) lies below the gypsum/bassanite transition (0.746 at 98 C, LLNL log K(T)). The block makes 1,427 t/d of P2O5 as a 42.0 wt% P2O5 filter acid, the strength UNIDO quotes its HH filtration rate at and inside Prayon's 40-42% for its HH process, with no concentration step. The price is the water balance the EFMA BAT booklet on phosphoric acid names as the HH drawback: a 42% acid leaves room for a wash ratio of only 1.74 on the three countercurrent stages, so 6.4% of the P2O5 stays in the cake as soluble acid and recovery is 89.7%, just under the 90-94% EFMA and the 92-94% Prayon give for a good HH plant (the attack efficiency and co-crystallized fraction are kept at the dihydrate showcase's values, so the difference is the wash). Fluorine is split 38% to the gas, 50% to the cake and 12% to the acid, EFMA's typical hemihydrate distribution (reactor off-gas plus flash-cooler vapour). The flash cooler removes 17.8 MW by evaporating 7.8 kg/s of water. The tilting-pan filter is sized by Ruth's constant-pressure law at the same vacuum (14.5 inHg), 3 min cycle and 18 s formation time as the dihydrate showcase (Pillai et al., US 5,185,135): 204 m2 at 7.0 t P2O5/m2/day, UNIDO's typical hemihydrate filtration rate for 42% acid, limited by cake formation (the wash needs 48 s of its 81 s). The filtrate viscosity, 2.18 mPa s, is the pure H3PO4/water fit to NIST ThermoML data, extrapolated 33 K past its 338 K data at this temperature; the filtrate density, 1351 kg/m3, is Laliberte's (2009) H3PO4 correlation at 42% P2O5 and 98 C, extrapolated 17 K past its 81.4 C range. Both are for pure acid; wet-process acid is more viscous and denser. The cake's specific resistance, 4.35e8 m/kg, is back-calculated to the 7.0 t P2O5/m2/day, and it falls inside the Kozeny-Carman band for the 3-24 um hemihydrate crystals Huo et al. (ACS Omega 2023) grew at 95 C in 38% P2O5 acid (porosity bracket 0.35-0.55 assumed; bassanite 2.70 g/cm3). The cloth resistance (1e9 1/m) and the wash/dry sector split are the dihydrate showcase's, not sourced; the published rate bounds the cloth: no cloth tighter than 1.6e10 1/m reaches 7.0 at these settings. Scope, stated rather than implied: (1) one block for the attack tanks, flash cooler and filter, with no crystal-size model, so the cake resistance is an input; (2) the attack efficiency, co-crystallized fraction, fluorine split and cake liquor are plant inputs (UNIDO and EFMA say HH crystals are smaller and filter less easily, so a real HH cake may hold more liquor than the 0.40 kg/kg kept here); (3) no hemihydrate-to-gypsum rehydration on the cloth; (4) the water activity reads the P2O5 strength only; (5) anhydrite, the truly stable phase, is not considered.

The flowsheet

The solved topology — every unit op's real duty, conversion, or split, read straight off a genuine converged solve.

Phosphate ROCK
Sulfuric ACID
WASH Water
rock
acid
wash
gas
acid
cake
PAR
Filter ACID
Hemihydrate CAKE
OFF GAS

The stream table

Every stream's flow, temperature, pressure, and composition — real converged numbers, not placeholders.

See it live
Open this exact flowsheet in the workspace, already solved — tweak a spec and re-run.
Launch interactive model

Stop fighting legacy software. Build your first flowsheet in 60 seconds.