How to simulate industrial i-butane/n-butane splitter
A close-boiling isobutane/n-butane splitter as reported by Klemola and Ilme (Ind. Eng. Chem. Res. 1996, 35, 4579) — the relative volatility between the two isomers is small (~1.3), so the column needs many stages and a high reflux ratio for a sharp split, unlike the wider-boiling LPG splits elsewhere in this library.
- 1Open the ready-made model
Open the "Industrial i-butane/n-butane splitter" model in the MaximaLabs workspace — no install, no license. It loads live on the canvas, ready to edit and run.
- 2Confirm the thermodynamics
This process is modeled with the PENG-ROBINSON property package over isobutane, n_butane — already selected, so the phase equilibrium and enthalpy are physically consistent from the first run.
- 3Review the flowsheet
The flowsheet chains COL. Every block is a real, solvable unit op you can reconfigure on the canvas.
- 4Run the simulation
Click Run. The deterministic solver converges the material and energy balances (recycles included) and fills the live stream table — the AI never invents a number.
- 5Read the results and iterate
Inspect the converged streams, tweak a spec, and re-run — or ask the AI copilot to explain a result or diagnose a failed solve in plain English.
- Thermodynamics
- PENG-ROBINSON
- Components
- isobutane, n_butane
- Unit operations
- COL
Opens live on the canvas — free, no install.
Explore the model & flowsheetFrequently asked questions
- What does the Industrial i-butane/n-butane splitter model simulate?
- A close-boiling isobutane/n-butane splitter as reported by Klemola and Ilme (Ind. Eng. Chem. Res. 1996, 35, 4579) — the relative volatility between the two isomers is small (~1.3), so the column needs many stages and a high reflux ratio for a sharp split, unlike the wider-boiling LPG splits elsewhere in this library.
- Which thermodynamic method does it use?
- The PENG-ROBINSON property package, over isobutane, n_butane — already selected. You can switch the method on the canvas before running.
- Which unit operations are in the flowsheet?
- It chains COL. Every block is a real, solvable unit operation you can reconfigure, add to, or remove.
- Do I need to install software or buy a license?
- No. Industrial i-butane/n-butane splitter runs entirely in your browser on MaximaLabs — free, no install, no license. Open the model to load it live and run the deterministic solver.
More guides like this
Perry Ch.13 Example 3: butane/pentane splitter
A simple two-cut distillation splitting butane overhead from pentane bottoms, from Chapter 13 of Perry's Chemical Engineers' Handbook.
Perry Ch.13 Example 4: sloppy-butane three-cut splitter
A three-cut column with a side draw producing a deliberately 'sloppy' (off-spec, cheaper-to-make) butane cut between a propane overhead and a pentane-plus bottoms, from Chapter 13 of Perry's Chemical Engineers' Handbook.
Aromatics column (Strigle)
A simple aromatics splitter recovering benzene overhead from a toluene/xylene-heavy feed, as described by R. Strigle (Gulf Publishing, 1987) — a classic packed-column textbook design case.
Depropanizer (Strigle)
A depropanizer recovering propylene and propane overhead from a C₄-and-heavier hydrocarbon feed, as described by R. Strigle (Gulf Publishing, 1987).
Ethanol–water distillation
An 8-stage column concentrating ethanol overhead toward the azeotrope (the headline demo).
Tray efficiency — real trays vs ideal stages
The same ethanol–water column solved with a Murphree vapor tray efficiency of 0.7 instead of ideal equilibrium stages. A real sieve/valve tray never reaches full vapor-liquid equilibrium — the vapor leaving it only partly approaches the equilibrium composition with the tray liquid, mixing in un-equilibrated vapor from the tray below: y = E·K·x + (1−E)·y_below (Murphree 1925). At E = 0.7 each of these 12 trays does 70% of an ideal stage's work, so the overhead ethanol is lower than an equilibrium column of the same tray count would predict — which is exactly why a real column needs more trays than a shortcut (ideal-stage) calculation says. Both HYSYS and Aspen RadFrac expose this per-tray efficiency; set murphree_efficiency back to 1.0 to recover the ideal-stage column. The efficiency auto-selects the component-flow Naphtali-Sandholm solver (the reduced-form solvers carry no explicit per-tray VLE row to apply an efficiency to).