How to simulate plasmid dna — e. coli fermentation to clarified lysate
The front end of every plasmid DNA process — the template mRNA vaccines are transcribed from, and the DNA many diagnostics and gene therapies are built on: fermentation → harvest → alkaline lysis. 1 m³/h of medium carrying 20 g/L glucose grows E. coli to 10 g/L dry cells at a 0.25 1/h dilution rate, each cell holding 5 mg plasmid per g dry weight (49 g/h of plasmid). The cells are harvested and resuspended, then lysed the Birnboim-Doly way: P₂ (0.2 M NaOH, 1% SDS) and P₃ (3 M potassium acetate brought to pH 5.5 with acetic acid), 10 L each per kg of wet cells. What the lysis block computes rather than takes as given: the pH the NaOH sets during lysis, 12.51 at 37 °C (the classical denaturation window is pH 12-12.5, above which supercoiled plasmid starts to denature for good), the pH after neutralization, 5.79, both from the same aqueous speciation the neutralizer uses; the potassium dodecyl sulfate the neutralization precipitates, 4.2 kg/h, which is what traps the genomic DNA and debris; and the clarified lysate, 1.07 m³/h at 37 mg/L plasmid — a threefold dilution of the resuspended cells, which is what sizes the clarification and the UF/DF step after it. What it takes as measured inputs, because they are: the fraction of plasmid that survives into the lysate (here 80%) and the fraction of the biomass that flocculates (95%). Both depend on the host, the plasmid and above all on how the lysate is mixed — shear fragments genomic DNA into pieces small enough to slip through the floc — and no correlation predicts them; the values here are illustrative. The fermentation is a chemostat, a continuous stand-in for the fed-batch a real plasmid process runs (use the fed-batch tool for the transient); the Monod constants are typical E. coli-on-glucose values, illustrative too. The lysis pH is the NaOH alone (P₁'s Tris and the cells' own buffering pull it a little lower), activity coefficients are screening-grade at the ~1 M ionic strength after P₃, and the reagent salts are reported rather than carried as components. Downstream (TFF, anion-exchange capture, polishing) uses the same blocks as the mAb train.
- 1Open the ready-made model
Open the "Plasmid DNA — E. coli fermentation to clarified lysate" model in the MaximaLabs workspace — no install, no license. It loads live on the canvas, ready to edit and run.
- 2Confirm the thermodynamics
This process is modeled with the NRTL property package over glucose, water — already selected, so the phase equilibrium and enthalpy are physically consistent from the first run.
- 3Review the flowsheet
The flowsheet chains FERM, Harvest, Lysis. Every block is a real, solvable unit op you can reconfigure on the canvas.
- 4Run the simulation
Click Run. The deterministic solver converges the material and energy balances (recycles included) and fills the live stream table — the AI never invents a number.
- 5Read the results and iterate
Inspect the converged streams, tweak a spec, and re-run — or ask the AI copilot to explain a result or diagnose a failed solve in plain English.
- Thermodynamics
- NRTL
- Components
- glucose, water
- Unit operations
- FERMHarvestLysis
Opens live on the canvas — free, no install.
Explore the model & flowsheetFrequently asked questions
- What does the Plasmid DNA — E. coli fermentation to clarified lysate model simulate?
- The front end of every plasmid DNA process — the template mRNA vaccines are transcribed from, and the DNA many diagnostics and gene therapies are built on: fermentation → harvest → alkaline lysis. 1 m³/h of medium carrying 20 g/L glucose grows E. coli to 10 g/L dry cells at a 0.25 1/h dilution rate, each cell holding 5 mg plasmid per g dry weight (49 g/h of plasmid). The cells are harvested and resuspended, then lysed the Birnboim-Doly way: P₂ (0.2 M NaOH, 1% SDS) and P₃ (3 M potassium acetate brought to pH 5.5 with acetic acid), 10 L each per kg of wet cells. What the lysis block computes rather than takes as given: the pH the NaOH sets during lysis, 12.51 at 37 °C (the classical denaturation window is pH 12-12.5, above which supercoiled plasmid starts to denature for good), the pH after neutralization, 5.79, both from the same aqueous speciation the neutralizer uses; the potassium dodecyl sulfate the neutralization precipitates, 4.2 kg/h, which is what traps the genomic DNA and debris; and the clarified lysate, 1.07 m³/h at 37 mg/L plasmid — a threefold dilution of the resuspended cells, which is what sizes the clarification and the UF/DF step after it. What it takes as measured inputs, because they are: the fraction of plasmid that survives into the lysate (here 80%) and the fraction of the biomass that flocculates (95%). Both depend on the host, the plasmid and above all on how the lysate is mixed — shear fragments genomic DNA into pieces small enough to slip through the floc — and no correlation predicts them; the values here are illustrative. The fermentation is a chemostat, a continuous stand-in for the fed-batch a real plasmid process runs (use the fed-batch tool for the transient); the Monod constants are typical E. coli-on-glucose values, illustrative too. The lysis pH is the NaOH alone (P₁'s Tris and the cells' own buffering pull it a little lower), activity coefficients are screening-grade at the ~1 M ionic strength after P₃, and the reagent salts are reported rather than carried as components. Downstream (TFF, anion-exchange capture, polishing) uses the same blocks as the mAb train.
- Which thermodynamic method does it use?
- The NRTL property package, over glucose, water — already selected. You can switch the method on the canvas before running.
- Which unit operations are in the flowsheet?
- It chains FERM, Harvest, Lysis. Every block is a real, solvable unit operation you can reconfigure, add to, or remove.
- Do I need to install software or buy a license?
- No. Plasmid DNA — E. coli fermentation to clarified lysate runs entirely in your browser on MaximaLabs — free, no install, no license. Open the model to load it live and run the deterministic solver.
More guides like this
Substrate-inhibited fermenter (Haldane kinetics)
A continuous chemostat where growth is genuinely inhibited at high substrate concentration — the real Haldane mechanism (mu = mu_max*S/(Ks + S + S^2/Ki)), a native solver kinetics option (params['ki']), not a decorative custom block (custom_block structurally can't change stream composition, so faking this through one would misrepresent the reactor's actual material balance). At the same dilution rate a plain Monod fermenter would consume nearly all the feed substrate; here more substrate survives unconverted and less biomass forms, because growth is suppressed in this concentration range — the whole point of modeling inhibition at all. A strongly inhibitory Ki can also make a nominally achievable dilution rate (D < mu_max) physically unreachable and the reactor washes out, since the Haldane mu(S) curve peaks at a finite S and falls again at higher S.
Bioreactor (Monod fermenter)
A steady-state chemostat: substrate is consumed by Monod growth (μ = μmax·S/(Ks + S)) to produce biomass — a modern reactor model legacy tools lack.
Media-prep + Monod fermenter
A production bioprocess step: the growth medium is preheated to fermentation temperature, then a Monod chemostat consumes the substrate to build biomass — the media conditioning + fermentation train around the reactor.
Continuous mAb: perfusion bioreactor into TFF concentration
The upstream and downstream halves of a biologics process on one canvas. A perfusion bioreactor produces a cell-free harvest, and the antibody in it is then concentrated by tangential-flow filtration — the step every biologics process ends with. The membrane is a per-species rejection, which is what makes UF/DF a genuine steady-state unit rather than something that has to be pretended into one: the antibody is fully retained while the spent substrate and lactate pass freely into the permeate. The split is not asserted — it follows from the concentration target, and the flux the membrane can actually deliver at the resulting wall concentration is what sets the area. The polarization is the point. Retained protein piles up at the membrane wall far above the bulk, and it is the wall concentration that sets the osmotic back-pressure — which is why ultrafiltration flux plateaus with pressure instead of rising with it, and why a specified-recovery membrane model cannot represent this step at all. Bounded, and inherited from the underlying model: no fouling or time-dependent resistance growth, and the virial coefficients that set a protein's osmotic pressure are caller inputs because they are measured per protein per formulation — no protein databank ships with this.
Monoclonal antibody — perfusion culture to freeze-dried vial
A monoclonal antibody from the perfusion culture that makes it to the freeze-dried vial: culture → capture → viral inactivation → virus filtration → UF/DF → lyophilization. Every downstream step was a standalone calculator before this; wiring them together is what makes the train's numbers agree with each other — raise the culture's productivity and the capture column, the filter area and the vial count all move with it. The protein enters as a product, not a feed. No property databank carries a 148 kDa antibody (a biomolecule databank is a licensed-data gap, not a missing formula), so the mAb is produced by the bioreactor rather than declared on a feed — a feed component has to be priced thermodynamically, and this one cannot be. Capture (PROTEIN_A). Sized on dynamic binding capacity via Bohart-Adams, the model derived for the near-irreversible isotherm a Protein A resin has — the rigorous bed PDE does not converge at a ~1e-3 g/L dissociation constant, so the method here is the one process development actually uses. Titre and harvest volume come from the feed stream, so changing the upstream titre resizes the column. Viral inactivation (LOW_PH_HOLD). The kill is biphasic: the resistant fraction imposes a hard −log₁₀(f) ceiling, so a longer hold stops helping. single-population fit would promise unlimited kill and justify a hold that cannot deliver — raise target_log_reduction past the ceiling and the step says so instead of reporting a number. Virus filtration (VIRUS_FILTER). Sized on capacity, not flux: the filter plugs, so throughput climbs toward Vmax and never past it. That is why more pressure does not rescue an undersized filter, and why the step reports throughput against capacity. UF/DF (UFDF). Film-theory polarization and the virial osmotic-pressure flux equation solved together — which is what produces the pressure-independent plateau that defines ultrafiltration. Raise the TMP and watch the flux barely move while the wall concentration climbs; raise the mass-transfer coefficient (crossflow) instead and it responds. The reverse-osmosis membrane op structurally cannot show that. Freeze drying (LYO). Primary drying by the Pikal vial model, with the collapse margin the cycle actually has to respect. Push the shelf temperature up and the cycle shortens right up until the product crosses its collapse temperature and the batch is lost. No biologics data ships, deliberately. Every number that decides an answer here — resin capacity and rate constant, the virus kill rate and Vmax, the protein's second virial coefficient, the vial heat-transfer coefficient and cake resistance — is measured for your molecule, your resin, your dryer. The values in this example are illustrative and each step refuses rather than defaulting when one is missing. Bounds. Screening-grade process development, not a tech-transfer package: pH elution is a declared yield rather than a desorption model, the ICH Q5A clearance budget across steps lives in the Viral clearance tool (a budget spans steps), and no GMP artefacts — batch records, 21 CFR Part 11 — exist here.
Lignocellulosic ethanol — pretreatment + enzymatic hydrolysis + real fermentation
The bioresource-engineering gap this closes: two existing 'corn-ethanol' showcases in this catalog (superheated-steam-drying-loop, bioethanol-mvr-stillage) are both downstream-only — drying and distillation on an already-fermented feed or a generic surrogate solid, with no bioreactor anywhere in either flowsheet. This is the first biofuel showcase that actually runs a real fermentation: pretreatment (dilute-acid/steam) solubilizes part of the lignocellulosic feed into fermentable sugars, the existing generic enzymatic_reactor (Michaelis-Menten) saccharifies the cellulose fraction left behind, and the existing bioreactor (Monod chemostat) ferments the resulting sugar to ethanol — the real kinetics kernel, not a spec-based separator standing in for the biology. Bounded, and stated plainly: the pretreatment conversion fraction (hemicellulose → sugar) is a caller-specified design input — a measured/vendor yield, not a predicted dilute-acid severity-factor (log R0) correlation; inventing one would fabricate exactly the number this flowsheet's answer depends on. Real lignocellulose chemistry (cellulose, hemicellulose, xylose, glucose) carries no enthalpy or density data anywhere in MaximaLabs's thermo databank — every sugar was checked directly and none has a liquid-density or ideal-gas-Cp correlation, so a flowsheet naming them by their real identities cannot solve at all. Real, differently-named organics with full databank coverage stand in 1:1 instead (glycerol for the lignocellulosic solid, acetic acid for the hemicellulose-derived sugar liquor, methanol for glucose) — the same generic-surrogate posture already established elsewhere in MaximaLabs (e.g. ethanol standing in as the dissolved substrate in the perfusion-bioreactor tests). Ethanol itself is the one real target molecule in the chain — no surrogate needed. Kinetic constants (mu_max, Vmax, Km, yields) are illustrative, not fit to a published fermentation study — the same posture the LHHW methanol-synthesis showcase states for its own rate law. The pentose-sugar liquor from pretreatment is not fermented in this showcase (many industrial processes do not ferment it with ordinary yeast either) — it reports to its own product stream rather than being silently discarded. No downstream distillation is attempted: a rigorous VLE column needs every component priceable, and the fermentation broth carries an unpriced 'biomass' pseudo-component (the same class of limitation this session's Gibbs-reactor work hit with elemental carbon) — ethanol recovery is the documented next real step, not modeled here.