MaximaLabs
All guides
Phosphate fertilizer complex (EFMA standard 50 t/h NPK train)

How to simulate npk 15-15-15 granulation (mixed-acid route)

A 50 t/h NPK 15-15-15 granulation plant on the mixed-acid route (EFMA BAT Booklet No. 8, s. 2.1-2.2: the booklet's own standard grade and rate). Phosphoric acid of Handley's (IFA 1984) analysis is ammoniated in a pre-neutralizer to mole ratio 1.45, the solubility maximum on Ivell's (IFA 1984) crystallisation chart; the slurry's water is not typed in but read off that chart at 114 °C: 16.1%. In the granulator the slurry meets a 92% ammonium nitrate solution (Booklet No. 6: up to 8% water for granulation), solid potassium chloride, dolomite filler and the recycle, and more ammonia takes the phosphate to mole ratio 1.53, the ratio the booklet's own pipe-reactor raw-material table implies. (1) The feed rates are not tuned: they are the exact solution of the formulation balances (N, P₂O₅, K₂O, mass and the mole ratio) for 15-15-15 at 1 wt% moisture, from these raw materials, with the coating fixed: 377.8 kg acid, 312.1 kg AN solution, 237.4 kg KCl, 152.4 kg filler and 60.4 kg ammonia per tonne. Against the booklet's 95%-water-soluble pipe-reactor column (nitric acid 242, ammonia 122, P₂O₅ 154, potash 250, filler 150 kg/t) the same solver reproduces its numbers within 3% where the raw materials agree. (2) The product leaves the coating drum at 15.0-15.0-15.0 as-is, 13.89 kg/s (50.0 t/h), with 0.50 kg/t of fatty amine and 9.0 kg/t of kaolin, inside the published anti-caking doses (Breiss, ISMA 1970: 0.4-1.0 kg/t of formulated amine, 8-10 kg/t of mineral charge; GNFC run 0.5 kg/t). The coating dilutes the grade by 0.95%, which the formulation pays for in advance. (3) Recycle ratio 4.5, between Ivell's 'under 4' for a pressure neutralizer and 5-6 for atmospheric systems; product cooled to 315 K. (4) What is an input, and why: the ammonia slips of both reactors and the scrubber recoveries are plant measurements (no measured NH₃ vapour pressure over ammonium phosphate slurries was found to compute them). The pre-neutralizer is specified the way a plant quotes it, by the ammonia in its vapour: 0.05 kg NH₃ per kg water, the figure Houghtaling & Margiotti (IFA 1994) give for a commercial DAP reactor; the slip that follows is 6.8% of the ammonia fed. (Handley's IFDC pilot-plant slip of 0.29 would put 0.21 kg/kg in the vapour.) The granulator's 0.20 slip is representative, not measured. The stack loses 0.046 kg NH₃/t, inside the booklet's 0.06 kg/t BAT level for two 90% scrubbers. (5) At 114 °C and 16% slurry water from 54% P₂O₅ acid the pre-neutralizer rejects 0.34 MW: with little ammonia slipping, most of the neutralisation heat is released in this vessel, more than boiling off the water needs. (6) Bounded: KCl + NH₄NO₃ exchange (to KNO₃ + NH₄Cl) is not modelled (extent 0, an input); the potash is pure KCl (63.2% K₂O) where commercial potash is 60%; the 92% AN solution is priced as crystal plus its 3-H₂O solution below NBS's first row; Ivell's chart is for pure ammonium phosphate solutions.

ACID
NH3 PN
NH3 GR
gas
acid
gas
liq
byp
TAIL
gas
acid
gas
liq
byp
PRE
acid
NH3
slurry
vap
NH3
PN
rec
slurry
solids
NH3
gran
gas
NH3
GR
wet
dry
vap
DRY
feed
over
under
SCR1
feed
over
under
SCR2
Crush
Split
feed
gas
elut
solid
COOL
COOL AIR
Product
Stack
Dryer Vapor
NH3 Return PN
NH3 Return GR
Cooler GAS
AN SOL
Potash
Filler
COAT OIL
COAT Powder
prod
coat
out
COAT
  1. 1
    Open the ready-made model

    Open the "NPK 15-15-15 granulation (mixed-acid route)" model in the MaximaLabs workspace — no install, no license. It loads live on the canvas, ready to edit and run.

  2. 2
    Confirm the thermodynamics

    This process is modeled with the PR-STEAM property package over water, ammonia, phosphoric_acid, sulfuric_acid, monoammonium_phosphate, diammonium_phosphate, ammonium_sulfate, phosphate_impurities, n2, o2, ammonium_nitrate, potassium_chloride, dolomite, fatty_amine, kaolinite, potassium_nitrate, ammonium_chloride — already selected, so the phase equilibrium and enthalpy are physically consistent from the first run.

  3. 3
    Review the flowsheet

    The flowsheet chains 2× PRE, PN, GR, DRY, 2× SCR2, Crush, Split, COOL, COAT. Every block is a real, solvable unit op you can reconfigure on the canvas.

  4. 4
    Run the simulation

    Click Run. The deterministic solver converges the material and energy balances (recycles included) and fills the live stream table — the AI never invents a number.

  5. 5
    Read the results and iterate

    Inspect the converged streams, tweak a spec, and re-run — or ask the AI copilot to explain a result or diagnose a failed solve in plain English.

What you'll build
Thermodynamics
PR-STEAM
Components
water, ammonia, phosphoric_acid, sulfuric_acid, monoammonium_phosphate, diammonium_phosphate, ammonium_sulfate, phosphate_impurities, n2, o2, ammonium_nitrate, potassium_chloride, dolomite, fatty_amine, kaolinite, potassium_nitrate, ammonium_chloride
Unit operations
2× PREPNGRDRY2× SCR2CrushSplitCOOLCOAT
Open this model in the workspace

Opens live on the canvas — free, no install.

Explore the model & flowsheet

Frequently asked questions

What does the NPK 15-15-15 granulation (mixed-acid route) model simulate?
A 50 t/h NPK 15-15-15 granulation plant on the mixed-acid route (EFMA BAT Booklet No. 8, s. 2.1-2.2: the booklet's own standard grade and rate). Phosphoric acid of Handley's (IFA 1984) analysis is ammoniated in a pre-neutralizer to mole ratio 1.45, the solubility maximum on Ivell's (IFA 1984) crystallisation chart; the slurry's water is not typed in but read off that chart at 114 °C: 16.1%. In the granulator the slurry meets a 92% ammonium nitrate solution (Booklet No. 6: up to 8% water for granulation), solid potassium chloride, dolomite filler and the recycle, and more ammonia takes the phosphate to mole ratio 1.53, the ratio the booklet's own pipe-reactor raw-material table implies. (1) The feed rates are not tuned: they are the exact solution of the formulation balances (N, P₂O₅, K₂O, mass and the mole ratio) for 15-15-15 at 1 wt% moisture, from these raw materials, with the coating fixed: 377.8 kg acid, 312.1 kg AN solution, 237.4 kg KCl, 152.4 kg filler and 60.4 kg ammonia per tonne. Against the booklet's 95%-water-soluble pipe-reactor column (nitric acid 242, ammonia 122, P₂O₅ 154, potash 250, filler 150 kg/t) the same solver reproduces its numbers within 3% where the raw materials agree. (2) The product leaves the coating drum at 15.0-15.0-15.0 as-is, 13.89 kg/s (50.0 t/h), with 0.50 kg/t of fatty amine and 9.0 kg/t of kaolin, inside the published anti-caking doses (Breiss, ISMA 1970: 0.4-1.0 kg/t of formulated amine, 8-10 kg/t of mineral charge; GNFC run 0.5 kg/t). The coating dilutes the grade by 0.95%, which the formulation pays for in advance. (3) Recycle ratio 4.5, between Ivell's 'under 4' for a pressure neutralizer and 5-6 for atmospheric systems; product cooled to 315 K. (4) What is an input, and why: the ammonia slips of both reactors and the scrubber recoveries are plant measurements (no measured NH₃ vapour pressure over ammonium phosphate slurries was found to compute them). The pre-neutralizer is specified the way a plant quotes it, by the ammonia in its vapour: 0.05 kg NH₃ per kg water, the figure Houghtaling & Margiotti (IFA 1994) give for a commercial DAP reactor; the slip that follows is 6.8% of the ammonia fed. (Handley's IFDC pilot-plant slip of 0.29 would put 0.21 kg/kg in the vapour.) The granulator's 0.20 slip is representative, not measured. The stack loses 0.046 kg NH₃/t, inside the booklet's 0.06 kg/t BAT level for two 90% scrubbers. (5) At 114 °C and 16% slurry water from 54% P₂O₅ acid the pre-neutralizer rejects 0.34 MW: with little ammonia slipping, most of the neutralisation heat is released in this vessel, more than boiling off the water needs. (6) Bounded: KCl + NH₄NO₃ exchange (to KNO₃ + NH₄Cl) is not modelled (extent 0, an input); the potash is pure KCl (63.2% K₂O) where commercial potash is 60%; the 92% AN solution is priced as crystal plus its 3-H₂O solution below NBS's first row; Ivell's chart is for pure ammonium phosphate solutions.
Which thermodynamic method does it use?
The PR-STEAM property package, over water, ammonia, phosphoric_acid, sulfuric_acid, monoammonium_phosphate, diammonium_phosphate, ammonium_sulfate, phosphate_impurities, n2, o2, ammonium_nitrate, potassium_chloride, dolomite, fatty_amine, kaolinite, potassium_nitrate, ammonium_chloride — already selected. You can switch the method on the canvas before running.
Which unit operations are in the flowsheet?
It chains 2× PRE, PN, GR, DRY, 2× SCR2, Crush, Split, COOL, COAT. Every block is a real, solvable unit operation you can reconfigure, add to, or remove.
Do I need to install software or buy a license?
No. NPK 15-15-15 granulation (mixed-acid route) runs entirely in your browser on MaximaLabs — free, no install, no license. Open the model to load it live and run the deterministic solver.

More guides like this

Phosphate fertilizer complex (JESA-scale DAP train)

DAP granulation loop: pre-neutralizer, ammoniating granulator, scrubbers

Diammonium phosphate at the scale of one Jorf Lasfar (JESA) granulation train: 40.2 kg/s (145 t/h) of wet-process phosphoric acid is neutralised by ammonia in two steps and granulated in a loop that recycles four times its own product. The acid carries the composition Handley (IFA, 1984) gives for a commercial merchant-grade acid, per 100 g: 54.82 g H₃PO₄ (39.7% P₂O₅), 3.90 g H₂SO₄, 5.68 g of metal and fluoride impurities (carried as one inert lump) and 35.60 g water. It is pumped first through the tail-gas scrubber and the pre-scrubber, which take back the ammonia the reactors do not absorb, then into the pre-neutralizer, which holds a mole ratio NH₃:H₃PO₄ of 1.44 at 114 °C (near the ratio of highest ammonium phosphate solubility, so the least water keeps the slurry fluid) and boils off water with its own reaction heat. The slurry is sprayed onto the rolling bed of the ammoniating granulator, where sparged ammonia lifts the ratio to 1.845. New solid layers onto the recycled granules (an equal-thickness growth law on the full size distribution), the bed is dried to 3% moisture, a double-deck screen splits it at 3.35 and 1.70 mm, the oversize is crushed, and fines, crushed oversize and 73% of the on-size go back to the granulator. The rest is cooled and sold. The 73% is the split that puts the loop at the recycle ratio Handley reports, 4: a plant sets its recycle to absorb the slurry's water, so here it is an input, not a prediction. Solved: 33.7 kg/s of product (121 t/h), 18.7% N and 47.6% P₂O₅ on a dry basis, above the 18-46-0 commercial grade, which is set by the acid's sulfate and impurities rather than by the 21.2-53.8 of pure DAP. Consumption per tonne of product is 0.227 t NH₃ and 0.474 t P₂O₅. An 18-46-0 product carries 0.219 t of NH₃ as nitrogen and 0.46 t of P₂O₅ per tonne by its grade alone; the difference is this product's richer grade and the ammonia lost at the stack. The recycle ratio is 4.0, and the loop converges on its own tear machinery (six tears, Wegstein). The pre-neutralizer releases 19.1 MW of reaction heat and evaporates 7.3 kg/s of water; the granulator releases 6.9 MW and evaporates 5.2 kg/s; the dryer takes 1.7 kg/s more for 7.1 MW. 0.029 kg/s of ammonia leaves the stack, 0.4% of what is fed, which is what two scrubbers at 90% recovery each give.

Corn-ethanol biorefinery / distillers'-grains dryer, Blair, Nebraska, USA

Superheated-steam drying loop with MVR heat recovery

A wet cake is dried in a superheated-steam dryer (steam as the drying medium instead of hot air), and the evaporated moisture — pure steam — is recovered by mechanical vapor recompression (MVR) plus a trim superheater into high-grade superheated steam that reheats the recirculating drying medium. Superheated-steam drying is the energy-efficient route for biofuel and food solids (distillers' grains, beet pulp, lignite): because the drying atmosphere is steam, the evaporated water leaves as more steam whose latent heat is recompressed and reused, instead of being lost in a humid exhaust.

Ludwigshafen, Germany

Crystallization + granulation finishing

A continuous MSMPR crystallizer, cake filter, and dryer feed a granulator that grows the dried crystals into free-flowing granules — the finished-product train after the mother liquor and dryer vapor leave.

Porsgrunn, Norway

Green urea synthesis

Green ammonia and captured CO₂ react over a single-pass stoichiometric reactor (2NH₃ + CO₂ ⇌ CO(NH₂)₂ + H₂O) at synthesis-loop conditions — the fertilizer step downstream of green ammonia. Screening fidelity: a real plant recycles the unconverted carbamate/excess ammonia to push per-pass yield well above this single-pass conversion; that recycle isn't modeled here.

Rotterdam, Netherlands

Thermal (non-catalytic) HDA — broad aromatics feedstock

A real thermal-HDA licensor's process (non-catalytic, tolerant of a mixed aromatics feedstock and inert impurities) modeled as a genuine competing-and-sequential reaction network in a real plug-flow reactor, not a fixed-Keq equilibrium reactor like the simpler hda-toluene-dealkylation example. The main toluene dealkylation (toluene + H₂ → benzene + methane) uses real published kinetics: (-r_toluene) = k0exp(-Ea/RT)C_toluene*C_H2^0.5 (order 1 in toluene, order 0.5 in H₂, the classic 1.5-order thermal-HDA rate law), k0 = 5.67e9 (m3/mol)^0.5/s, Ea = 228,200 J/mol, heat of reaction -49,000 J/mol — transcribed from Shull & Hixon (Ind. Eng. Chem. Process Des. Develop. 5, 147, 1966) as tabulated in Rase, H.F., 'Chemical Reactor Design for Process Plants, Vol. 2: Case Studies and Design Data' (Wiley-Interscience, 1977), Case Study 104 'Toluene Dealkylation', pp. 36-42 (unit-converted from the source's imperial (ft, lb-mol, degR) basis to SI). That same source explicitly states 'rate equations for the side reactions have not been reported' — so the coking/heavies side reaction (2 benzene → biphenyl + H₂, the real reaction that caps aromatic yield below 100% and drives decoking intervals) and the xylene demethylation feeding the shared toluene pool (o-xylene + H₂ → toluene + methane — the real single-methyl-loss pathway, not a lumped double-dealkylation straight to benzene, so this is a genuine reactions-in-series-and-parallel network, not three independent reactions) both stay illustrative order-of-magnitude Arrhenius parameters, tuned only to land in the source's cited ~98% main-reaction selectivity at 2:1 H₂:toluene — honestly labeled as such, not fabricated citations. H₂S/CO₂/ammonia ride through the flowsheet as inert impurities — exactly what 'impurity tolerance' means in a mass balance, not a special chemistry path. A real fired heater (rigorous combustion stoichiometry + stack energy balance, the same unit op used in the naphtha-steam-cracker example) brings the mixed fresh-plus-recycle feed up to reaction temperature — not a feed specified as already at 950 K. The H₂-rich high-pressure separator vapor is a real recycle loop: fresh feed joins recycled gas at a mixer ahead of the furnace, and past the separator the vapor splits into a recompressed recycle (85%) and a genuine purge (15%) that bleeds off the methane a single pass could never consume — the same role a purge plays in the ammonia-synthesis-loop example. Quench, the high-pressure separator, and a letdown-valve-plus-flash stabilizer strip dissolved H₂/methane before the aromatics split. The reactor is genuinely adiabatic, not isothermal: temperature is a real energy-balance-coupled ODE state (the adiabatic PFR mode) that rises along the reactor length as the exothermic reactions release heat — starting from the furnace's real ~900 K outlet (in the source's cited 894-922 K inlet range) and climbing as the reaction proceeds, self-consistent: the reactor's external duty, which an adiabatic reactor must have at zero, comes out at about 0.03% of the heat its reactions release (checked by its test, not assumed). One honest simplification remains: the final benzene/toluene/xylene-derived-benzene split still uses a shortcut separator rather than a rigorous column, for the same documented reason as hda-toluene-dealkylation: trace H₂/methane corrupts the column's wide-boiling initial-guess classification, and a fix narrowed to just that seed broke the shipped methanol-synthesis example when tried previously.

Yara Porsgrunn, Norway

Ammonia synthesis loop (Haber-Bosch, ChemSep casebook)

The classic industrial ammonia loop: fresh syngas joins recycled unconverted gas, reacts over an equilibrium reactor (N₂ + 3H₂ ⇌ 2NH₃) at synthesis conditions, is chilled to condense high-purity liquid ammonia, and the remaining vapor splits into a recycle (back to the loop) and a purge — the purge exists specifically to bleed off the inert argon a single-pass reactor could never consume, which would otherwise concentrate in the recycle forever.

Stop fighting legacy software. Build your first flowsheet in 60 seconds.