MaximaLabs

Arsenic trioxide Process Flowsheets & Simulations

Explore 2 validated, solved Arsenic trioxide simulation flowsheets in MaximaLabs — real components: oxygen, nitrogen, sulfur_dioxide, sulfur_trioxide, water, skutterudite. Open any one directly in your browser.

Solved via: PENG-ROBINSON, BRINE.

Concentrate
AIR
feed
air
gas
calc
dust
Roaster
AS Cooler
GAS Cleaning
Preheater
Converter
Absorber
Calcine
DUST
White Arsenic
Scrubber Bleed
ACID
TAIL GAS
Cobalt arsenide roasting, Bou-Azzer-type concentrate (representative)

Cobalt arsenide roasting: de-arsenication, white arsenic and acid-plant gas

A cobalt arsenide concentrate is roasted to drive its arsenic off as As₄O₆ vapour before the calcine is leached for cobalt; the arsenic is recovered from the gas as white arsenic and the sulfur goes on to a sulfuric acid plant. The concentrate is REPRESENTATIVE of a Bou-Azzer-type feed, not an assay: 5.0 kg/s dry of 12% skutterudite (CoAs₃), 8% cobaltite (CoAsS), 30% arsenopyrite (FeAsS), 5% pyrite and 45% quartz (5.3% Co, 27% As), with 6% moisture. The fluidized-bed roaster runs at 700 °C with 30% excess air; how far each mineral roasts is an input (95%, pyrite 98%). It balances every element and the energy on Robie & Hemingway (1995) and NBS (1982) formation enthalpies: the roast releases 14.16 MW, the bed rejects 5.35 MW to its cooling coils (autogenous; with no heat removed the products would leave at 1386 K), and the off-gas carries 6.33% SO₂, 4.88% O₂ and 1.79% As₄O₆. The cobalt leaves as Co₃O₄ because the gas's oxygen keeps it stable below 1169 K. 95% of the arsenic is volatilised and the calcine holds 1.88% As; 30% of the calcine is carried to the boiler as dust. The gas is then cooled to 150 °C, where As₄O₆'s vapour pressure over solid arsenic trioxide is 2.93 Pa (Welch & Duschak 1915, USBM Technical Paper 81, measured 100-300 °C): 99.84% of it condenses and a baghouse at 99% collection gives 1.67 kg/s of white arsenic, 98.84% of the arsenic in the gas. The same cooler run at 200 °C would recover 94.3% and at 250 °C 27.5%, which is why arsenic is collected cold. Cooling takes out 5.12 MW, 0.45 MW of it sublimation heat. Wet gas cleaning and drying remove the rest of the arsenic and the water, leaving 6.97% SO₂ for the converter, which oxidises 98% of it (one bed, an input) for the absorber.

14 unit ops • PENG-ROBINSON

27 0

View & open
Concentrate
AIR
feed
air
gas
calc
dust
Roaster
AS Cooler
White Arsenic
SO2 TO ACID Plant
Calcine MIX
solid
acid
PLS
residue
Leach
Leach ACID
Leach Residue
H2O2
Ferric Sulfate
LIME 1
liq
ox
Fe
lime
liq
As
xs
AS Scorodite
Scorodite Residue
Unused Reagents 1
LIME 2
liq
ox
Fe
lime
liq
As
xs
FE AS Polish
Ferric Arsenate Residue
Unused LIME 2
electrolyte
spent
cathode
gas
EW CU
Copper Cathode
CU CELL GAS
Caustic
liquor
reagent
out
excess
Neutralizer
Unused Caustic
CO Organic FEED
feed
solv
ext
raff
SX CO
Strip Liquor
feed
solv
ext
raff
Strip
Barren Organic
electrolyte
spent
cathode
gas
EW CO
Cathode Cobalt
Spent Electrolyte
CO CELL GAS
feed
clarified
sludge
NI Precip
Nickel Hydroxide
Barren Liquor
Strip MIX
CO Split
Spent Split
Sulph MIX
EVAP
EVAP Water
feed
solid
liq
CO Cryst
Cobalt Sulphate
ML Split
Mother Liquor Bleed
Guemassa, Morocco (representative flowsheet)

Guemassa-type cobalt refinery, roast-leach route (representative): roaster, white arsenic, calcine leach, scorodite polish, Cu EW, Cyanex 272, Co EW, CoSO4, Ni(OH)2

The guemassa-cobalt-refinery flowsheet with a de-arsenication roast in front of the leach, which is how arsenide concentrates are usually treated: the direct leach has to buy more iron than the concentrate carries to fix its arsenic as scorodite. Everything from the scorodite stage on is the same nodes as the direct-leach example. The concentrate is REPRESENTATIVE: the roasting example's mineralogy (12% skutterudite, 8% cobaltite, 30% arsenopyrite, 5% pyrite, 45% quartz) with nickel and copper as NiO and CuO at the Bou Azzer concentrate's Ni/Co and Cu/Co (Johnson et al. 2020), 1.40 kg/s dry with 6% moisture, sized to carry the direct-leach example's 73.5 g/s of cobalt. The fluidized-bed roaster at 700 C and 30% excess air (95% of each arsenide roasted, pyrite 98%, inputs) releases 3.90 MW and rejects 1.46 MW to its coils; the off-gas carries 6.32% SO₂. Cooled to 150 C, 0.46 kg/s of white arsenic condenses (98.84% of the arsenic in the gas, on Welch & Duschak's measured As₄O₆ vapour pressure); in all, 93.9% of the arsenic fed leaves as white arsenic, 1.1% stays in the gas, which goes to a product labelled 'to acid plant' (the acid plant is the roasting example's), and 5.0% stays in the calcine and dust, at 1.84% As. Calcine and dust are leached in sulfuric acid at 90 C, mineral by mineral (inputs: 95% of the Co₃O₄, NiO, CuO and unroasted sulfides and arsenides, 10% of the hematite; Co₃O₄ dissolving as Co(II) assumes a reductive leach whose reductant is not tracked), consuming 2.00 mol/s of acid. The liquor carries 978 mg/L As against 25,228 mg/L in the direct leach, and the iron the calcine dissolves puts its Fe:As at 1.82, so the scorodite stage buys no ferric iron (0.0 mol/s against 5.5 mol/s in the direct leach) and needs 0.18 mol/s of H₂O₂ (3.6), 3.60 mol/s of lime (11.18) and makes 0.05 kg/s of scorodite (1.40) and 0.61 kg/s of gypsum (1.92), leaving 0.03 mg/L As; its TCLP screen is 0.03 mg/L. The iron the scorodite does not need drops as ferrihydrite at pH 4 (0.021 kg/s). Downstream as in the direct-leach example: 95% of the copper plated, 0.5% of the nickel co-extracted by Cyanex 272, cobalt electrowon at 3.23 kWh/kg (0.022 kg/s of cathode), and CoSO₄.7H2O at 0.185 kg/s, about 5,826 t/y at 95.2% purity. Bounds: the roast conversions, dust carry-over, collection efficiency and leach fractions are inputs; skutterudite and cobaltite run on DFT heats of formation (see the roasting example); nickel and copper enter as oxides because the roaster has no Ni or Cu minerals, so the arsenic of the nickel arsenides a real Bou Azzer concentrate carries is missing; oxygen in the leach is not tracked; the SO₂ is not converted here.

48 unit ops • BRINE

30 0

View & open

Stop fighting legacy software. Build your first flowsheet in 60 seconds.